Poly-Fine® II Series Filter Cartridges product photo Primary L

Poly-Fine® II Series Filter Cartridges

Poly-Fine II cartridges are a proven filter solution for consistent and effective particle removal in liquid food and beverage applications.

Description

The Poly-Fine II element is a high area, pleated all-polypropylene depth filter frequently used in a wide variety of applications for particle removal. It is a cost-effective choice for final particle removal, or for pre-filtration, including reliable protection of final membrane filters.

Poly-Fine II filter media is the result of the latest in Pall proprietary technology and application expertise. Poly-Fine II media features a highly consistent pore structure with narrow pore size distribution, making it ideally suited for the capture of non-deformable contaminants, particulary those characterized by relatively narrow particle distribution.

Features and Benefits

 
Features Benefits
Proprietary melt blown, pleated media with high dirt holding capacity
  • Long service life
  • Consistent particulate retention and protection of final liquid membrane filters
  • Cost-effective filtration
   
 


Contact Us
* Required

Order Products

Narrow Your Results By

    Featured product
    Industries
    Brand
    Availability
    Cartridge Length (Imperial)
    Cartridge Length (Metric)
    Filter Media
    Gasket / O-Ring Material
Results Below
11
  • «
Cant find what you are looking for?
Contact a Pall Representative
Micron
0.8 µm
Unit of Measure
EA
Min Order Qty
1
Price
£ 140.79
Micron
5 µm
Unit of Measure
EA
Min Order Qty
1
Price
£ 134.09
Micron
10 µm
Unit of Measure
EA
Min Order Qty
1
Price
£ 95.45
Micron
10 µm
Unit of Measure
EA
Min Order Qty
12
Micron
10 µm
Unit of Measure
EA
Min Order Qty
1
Price
£ 134.09
Micron
30 µm
Unit of Measure
EA
Min Order Qty
1
Price
£ 140.79
  • «

Description

Poly-Fine II cartridges are a proven filter solution for consistent and effective particle removal in liquid food and beverage applications.

Description

The Poly-Fine II element is a high area, pleated all-polypropylene depth filter frequently used in a wide variety of applications for particle removal. It is a cost-effective choice for final particle removal, or for pre-filtration, including reliable protection of final membrane filters.

Poly-Fine II filter media is the result of the latest in Pall proprietary technology and application expertise. Poly-Fine II media features a highly consistent pore structure with narrow pore size distribution, making it ideally suited for the capture of non-deformable contaminants, particulary those characterized by relatively narrow particle distribution.

Features and Benefits

 
Features Benefits
Proprietary melt blown, pleated media with high dirt holding capacity
  • Long service life
  • Consistent particulate retention and protection of final liquid membrane filters
  • Cost-effective filtration
   
 

Specifications

Materials of Construction
 
Component Description
Filter Medium Polypropylene
Cage, Core, Find End and End Cap Polypropylene
SOE Style Cartridges only
Adaptor
Polypropylene
O-ring Seal Silicone Elastomer
Ethylene Propylene Rubber
DOE Style Cartridges only
Gasket
Ethylene Propylene Rubber
 

Food Contact Compliance

Please refer to the Pall website for a Declaration of Compliance to specific National Legislation and/or Regional Regulatory requirements for food contact use.

Technical Information

The technical information provided is based on controlled laboratory tests done on typical production filters at the conditions described, unless otherwise indicated. Actual operating conditions may affect the filter's performance.

Operating Characteristics1

 
Maximum Differential Pressure2 Operating Temperature
4.8 bard (70 psid) (forward) 20 °C (68 °F)
2.8 bard (40 psid) (forward) 65 °C (150 °F)
 
1Fluids which do not swell, soften or adversely affect any of the filter components
2Recommended change-out differential pressure is 2.4 bard (35 psid), provided the maximum differential pressure (based on temperature) is not exceeded.

Performance

Typical Flow Rates3



3Typical initial clean delta p per 254 mm (10 inch) cartridge, water at 20° C (68° F). For liquids with viscosity greater than 1cP, multiply the delta p by the viscosity.

Sterilization and Sanitization

Multiple autoclaving for 30 minutes at 1 bar (15 psig) steam (121 °C /250 °F) under no end load conditions, up to 10 cycles. In-line steam sterilization is not recommended. May be in-line sanitized with hot water at 82 °C (180 °F) for 1 hour.

Type

Filter Cartridges

Ordering Information

Ordering Information

This information is a guide to the part numbering structure and possible options. For availability of specific options please contact Pall. Refer to Pall for housing details.

Part Number: PFT [Table 1] [Table 2] U [Table 3] [Table 4] W 480
Example Part Number:PFT02530USM7W480
See bold reference code in tables.

Table 1:Removal Rating4

 
Code Description
90% Efficiency (Beta 10) >99.9% Efficiency (Beta 1000)
0.25 0.25 μm 1 μm
045 0.45 μm 1.2 μm
08 0.8 μm 2.5 μm
2 2 μm 5 μm
3 3 μm 7 μm
5 5 μm 12 μm
10 10 μm 15 μm
30 30 μm 40 μm
 
4Poly-Fine II filter cartridge liquid retention ratings are determined by a single pass test based on ASTM F-795 (see Pall Technical Bulletin 1903-4T). Removal efficiencies are shown at the stated rating in compatible fluids.

Table 2: Nominal Length

 
Code Description
DOE Style only:
975 248 mm (9.75")
10 254 mm (10")
195 495 mm (19.5")
20 508 mm (20")
2925 743 mm (29.25")
295 749 mm (29.5")
30 762 mm (30”)
39 991 mm (39")
40 1016 mm (40")
SOE Style only5:
10 254 mm (10")
20 508 mm (20")
30 762 mm (30")
40 1016 mm (40")
 
5Please contact Pall for specific dimensions of SI option cartridges.

Table 3: O-Ring / Gasket Seal Material

 
Code Description
S Silicone Elastomer6
E Ethylene Propylene Rubber
 
6for M3, M7, M8 options only

Table 4: Adaptor

 
Code Description
Blank DOE – with open end caps/gasket
M3 SOE – single open end with flat closed end and external 222 O-rings
M7 SOE – single open end with fin end, 2 locking tabs, and external 226 O-rings
M8 SOE – single open end with fin end and external 222 O-rings
SI SOE – with open end cap/gasket and integral stainless steel spring on flat closed end
 

Reviews

Earn 10% off* your next order online by leaving a review of this product. Please login to your account to leave a review. We appreciate and value your feedback.

*Subject to Terms and Conditions.