Description
High Capacity Pleated Polypropylene Filter Elements
- New, larger cartridge geometry
- High flow capacity
- Poly-Fine® II proprietary media for highly consistent filtration
- Inside-out flow traps contaminant inside the element
- Available to fit most Size 1 and Size 2 bag housings with no hardware changes
- Available in 101.6 cm (40 in) for use in unique 101.6 cm (40 in) Marksman housings
- Unique sealing device adjusts to fit in most bag filter housings
- High surface area for long service life
- All polypropylene construction
- Wide chemical compatibility
- Short length option to accommodate shorter baskets
For detailed information about this product, please refer to the data sheet. (To download this data sheet, select Download PDF from the menu above.)
Products in this datasheet may be covered by one or more patents, including US 7,473,360.Specifications
Product Specifications
Materials of construction
| Filter media: | Polypropylene |
| Hardware: | Polypropylene |
| Support material: | Polypropylene |
| Gaskets: | EPDM, fluorocarbon elastomer, nitrile |
| Sealing: | Thermal bond |
Dimensions (nominal)
| Outside flange diameter: | Three diameters are available.Contact Pall for information on sizes. |
| Outside filter diameter: | 15.2 cm (6 in) |
| Lengths: | Size 1 - Standard, Short Size 2 - Standard, Short, Extra Short Size 4 - 101.6 cm (40 in) |
Performance
Performance Specifications
Filter grades
1, 3, 5, 10, 20, 40, 70, 90, 150 micron (µm)
Maximum operating differential pressure
to 5.2 bard @ 20°C (75 psid @ 68°F)
to 2.4 bard @ 74°C (35 psid @ 165°F)
NOTE: Stainless steel flange recommended for temperatures in excess of 43°C (110°F).
Recommended change-out differential pressure1
2.4 bard @ up to 54°C (35 psid @ up to 130°F)
Food and water contact use
Please contact Pall Corporation to verify that the product conforms to your national legislation and/or regional regulatory requirements for water and food contact use.
Purity
Cartridges do not use surfactants, binders, and adhesives.
Sanitization
Contact Pall Corporation for assistance.
Particle Removal Ratings2 (µm)
| Cartridge Designation | 90% Efficiency | ≥99.9% Efficiency |
| PFTM 1 | 1 | - |
| PFTM 3 | 2 | - |
| PFTM 5 | - | 5 |
| PFTM 10 | - | 9 |
| PFTM 20 | - | 15 |
| PFTM 40 | 20 | - |
| PFTM 70 | - | 70 |
| PFTM 90 | 57 | - |
| PFTM 150 | - | 145 |
Typical Flow
| Filter Grade | mbard/lpm (psid/gpm) Water @ 20°C (68°F) | ||||
| Size 1 | Size 2 | 40 in | Size 1 (short) | Size 2 (short) | |
| 1 | 0.838 (0.046) | 0.364 (0.020) | 0.273 (0.015) | 0.765 (0.042) | 0.328 (0.018) |
| 3 | 0.346 (0.019) | 0.164 (0.008) | 0.109 (0.006) | 0.310 (0.017) | 0.128 (0.007) |
| 5 | 0.109 (0.006) | 0.054 (0.003) | 0.018 (0.001) | 0.109 (0.006) | 0.054 (0.003) |
| 10 | 0.054 (0.003) | 0.018 (0.001) | 0.018 (0.001) | 0.054 (0.003) | 0.018 (0.001) |
| 20 | 0.036 (0.002) | 0.018 (0.001) | 0.018 (0.001) | 0.036 (0.002) | 0.018 (0.001) |
| 40 | 0.018 (0.001) | 0.018 (0.001) | 0.018 (0.001) | 0.036 (0.002) | 0.018 (0.001) |
| 70 | 0.018 (0.001) | 0.018 (0.001) | 0.018 (0.001) | 0.018 (0.001) | 0.018 (0.001) |
| 90 | 0.018 (0.001) | 0.018 (0.001) | 0.018 (0.001) | 0.018 (0.001) | 0.018 (0.001) |
| 150 | 0.018 (0.001) | 0.018 (0.001) | 0.018 (0.001) | 0.018 (0.001) | 0.018 (0.001) |
NOTE: For kPa, multiply mbard/lpm by 0.1.
1 Provided that the maximum differential pressure is not exceeded based on temperature limits defined above.
2 Marksman PFT series filter cartridge retention ratings are based on Pall's Dynamic Efficiency test protocol. This single pass, destructive challenge test is based on ASTM F-795 test procedures for determining the performance of a filter medium. Fine test dust is used as the test contaminant for filters in the 1 to 20 micron range. Coarse test dust is used for micron ratings above 20 micron. Additional information can be obtained by contacting Pall Corporation. NOTE: PFTM grade designations for 1, 3, 40, and 90 based on Beta 10 values, and all other grade designations are based on Beta 1000 values.
Type
Large Format Filters
Ordering Information
Pall Part Number = PFTM [1] [2] - [3] U [4] - [5] [6]
Table 1
| Code | Short length option |
| Blank | Standard |
| S | Short |
| XS | Extra short 3, 4 |
Table 2
| Code | Filter grades (µm) |
| 1 | 1 |
| 3 | 3 |
| 5 | 5 |
| 10 | 10 |
| 20 | 20 |
| 40 | 40 |
| 70 | 70 |
| 90 | 90 |
| 150 | 150 |
Table 3
| Code | Cartridge lengths nominal |
| 1 | Size 1 bag |
| 2 | Size 2 bag |
| 4 | 101.6 cm (40 in) |
Table 4
| Code | Gasket materials |
| Blank | For NF version |
| N | Nitrile |
| E | EPDM (peroxide cured) |
| V | Fluorocarbon elastomer |
Table 5
| Code | End configurations |
| PF | Plastic self-adjusting flange |
| SF | Stainless steel self-adjusting flange (required for temperatures >43°C/110°F) |
| NF | No flange (for use with reusable SS flange) |
Table 6
| Code | Flange/gasket styles5 |
| A | Pall Marksman Series housings, Rosedale6,Strainrite, Krystil Klear7 |
| B | FSI BFNP Series housings (side entry), GAF8 |
| C | FSI FSPN Series housings (prior to June 2012 using a square counter bore), Hayward9 over the top |
3 Size 2 (only).
4 Select “XS" for Extra Short, “2" for Size 2 bag, and add “68" to the end of the part number (e.g., PFTMXS1-2UN-PFC 68).
5 For FSI FSPN Series housings (and other over the top housings) and FSI CBFP Series housings (side entry), consult your Pall FSI sales representative for proper flange/gasket style.
6 Rosedale is a registered trademark of Rosedale Products, Inc.
7 Krystil Klear is a registered trademark of Pentair Water Filtration.
8 GAF is a registered trademark of GAF Corporation.
9 Hayward is a registered trademark of Hayward Industrial Products, Inc.
Reviews
Earn 10% off* your next order online by leaving a review of this product. Please login to your account to leave a review. We appreciate and value your feedback.
*Subject to Terms and Conditions.
